Skip to main content

CCIE Practice LAB Dynamips

OK guys first I would like to thank you on the feedback it is much appreciated that some one takes the time to respond to you on your time and effort. So I would like to add another .net topology that is smaller but very useful for IP Services practice like Proxy Arp, NAT, HSRP and all the things you want to test that do not require a full lab of 13 routers. the lab was prepared from the IEWBv4 IPServices book under Advanced Technologies also to people that do not have this Work Book it can be very handy as it is not very hard to figure the structure of the lab. And work you way trough all kind of scenarios. So Here
2 comments

Popular posts from this blog

Step By Step MPLS – Basic MPLS Setup

Initial configuration , very basic with no MPLS, connectivity only to directly connected interfaces.R1R2R3R4!
!
!
interface Loopback0
ip address 1.1.1.1 255.255.255.255
!
interface FastEthernet0/0
ip address 10.0.31.1 255.255.255.0
duplex auto
speed auto
!
!
!
interface Loopback0
ip address 2.2.2.2 255.255.255.255
!
interface FastEthernet0/0
ip address 10.0.42.2 255.255.255.0
duplex auto
speed auto
!
!
!
interface Loopback0
ip address 3.3.3.3 255.255.255.255
no clns route-cache
!
interface FastEthernet0/0
ip address 10.0.31.3 255.255.255.0
duplex auto
speed auto
  no clns route-cache
!
interface Serial1/0
ip address 10.0.43.3 255.255.255.0
  serial restart-delay 0
no clns route-cache
!
!
!
interface Loopback0
ip address 4.4.4.4 255.255.255.255
no clns route-cache
!
interface FastEthernet0/0
ip address 10.0.42.4 255.255.255.0
duplex auto
speed auto
!
interface Serial1/0
ip address 10.0.43.4 255.255.255.0
  serial restart-delay 0
no clns route-cache
!
adding to the following configuration MPLS labels we will start wi…

VRF Maximum Routes

Maximum routes under customer vrf, if the service provider had unlimited resources he would not have needed that!
however normally resources are limited and expensive, and Service provider would like to make money from his available resources. maximum routes configured under VRF provide a mean of controlling PE local resource and abuse avoidance from the CE side.I have vrf called DC_EXTRANET, you can see that I have 16 routes, I have configured 10 maximum routes under that vrf however I did not want to be aggressive so I have set the warning only option. See that immediately I get a notice that I have more routes then the maximum, however no action is taken other then alerting and sending a syslog. ! PE_ashdod_otherisp.n(config-vrf)# maximum routes 10 warning-only % The current number of routes in the routing table is equal to, or exceeds the configured warning limit PE_ashdod_otherisp.n(config-vrf)# *Nov 26 20:39:41.175: %IPRT-3-ROUTELIMITWARNING: IP routing table limit warning - DC_…

ISIS Database Reading

ISIS is simple to operate normally while everything is working, most common deployments are flat network based on L2, however when there is a problem and we need to start troubleshooting then people start to get lost.So I would like to provide some tools on how to read ISIS database.notice to the “*” sign, that mean LSP was generated on the router you did the show command, you can see that host name from the show command match also host name on the LSPID,LSPID identified by hostname.xx-yy,  xx is normally 00 unless that LSP is pseudo node LSP generated by DIS , yy is representing the number of fragments for that LSP 00 – FF (max 255 fragments, plenty), most cases all the important information will be in 00 unless there are many fragments.LSP Holdtime is the amount of time an LSP will stay in database without any refresh.ATT/P/OL - 0/0/0, ATT bit or attached bit is used on L1/L2 connected to L1 node, if set to 1 L1 node will generate default route to the best L1/L2 node (best metric)AT…